The ADAM Audio Sub10 PRO is the bigger of the two new studio subwoofers from the Berlin brand. Where the Sub8 PRO serves compact nearfield setups, the Sub10 PRO is built for larger rooms and full-range systems around ADAM’s A Series monitors, including the A77H and A8H. It digs down to 21Hz, adds networked control and stores its room calibration inside the subwoofer. The US price is $1,499.99, and the subwoofer is available now.
A 10-inch driver in a bigger cabinet
The ADAM Audio Sub10 PRO uses a 10-inch fibre-reinforced paper cone with a rubber surround and a 45mm voice coil. It sits in a front-firing, front-ported cabinet of 450 x 360 x 450mm, made of vinyl-wrapped MDF with a painted MDF front. At 22.8kg, it is a serious piece of kit.

A Class D amplifier delivers 200 watts RMS into 3 ohms and 325 watts peak. That is the same amplifier as in the smaller model, so the extra depth comes from the larger driver and cabinet. The frequency response runs from 22Hz to 264Hz at -3dB, and from 21Hz to 300Hz at -6dB. That is almost a full octave lower than the Sub8 PRO, which stops at 30Hz at -3dB.
Output for bigger rooms
ADAM quotes a maximum peak SPL of 113dB at one metre with IEC-weighted noise, and 114dB with bass management at 85Hz. With sine bursts between 50 and 100Hz, the ADAM Audio Sub10 PRO reaches 106dB RMS and 110dB peak. Under the Dolby DARDT test, it reaches 113dB. Those figures make it suitable for medium-sized control rooms and immersive mixing studios.

Four operating modes are available: Remote Control, Local/Stereo, LFE and Wide. The LFE mode, below 120Hz, is tuned for Dolby Atmos systems. Bass management can be set to 70, 85, 100 or 115Hz, on the back panel or in software, and a footswitch input bypasses it while you check a mix.
Networked control and stored calibration
Like its smaller brother, the ADAM Audio Sub10 PRO connects over Ethernet, using the AES70 protocol, to ADAM Control. The free app for Windows and macOS manages complete A Series and Sub PRO systems. The internal DSP runs at 96kHz and offers phase in eight steps, up to 10ms of delay and four bands of parametric EQ. Calibration profiles from Sonarworks SoundID Reference are stored directly in the subwoofer, so the correction stays with the hardware.

Connections include two XLR/TRS combo inputs, two XLR outputs, and an AES3 digital input and output up to 24-bit/96kHz. For those who want a serious active hi-fi system built around ADAM monitors, the ADAM Audio Sub10 PRO is just as interesting as it is for a studio. Want the full story on the smaller model? Read our article on the ADAM Audio Sub8 PRO.
Pricing and availability
The ADAM Audio Sub10 PRO costs $1,499.99 (US MAP) and is available now. European pricing is available through the ADAM Audio EU shop. The warranty is two years, extended to five years after product registration. More information is on the ADAM Audio website.
Key specifications
- Driver: 10-inch fibre-reinforced paper cone, 45mm voice coil
- Amplifier: Class D, 200W RMS (3 ohms), 325W peak
- Frequency response: 22 – 264Hz (-3dB), 21 – 300Hz (-6dB)
- Max peak SPL: 113dB (IEC noise), 114dB (85Hz bass management)
- Bass management: 70, 85, 100 or 115Hz
- Modes: Remote Control, Local/Stereo, LFE, Wide
- Inputs: 2 x XLR/TRS combo, AES3 (24-bit/96kHz)
- Outputs: 2 x XLR, AES3
- Control: Ethernet (AES70), ADAM Control, Sonarworks SoundID Reference
- Dimensions and weight: 450 x 360 x 450mm, 22.8kg
- Price: $1,499.99 (US)
































